Chrysler список кодов ошибок

P1101 HCM/PCM Communication Performance 
P1103 Turbocharger Waste Gate Actuator Malfunction 
P1104 Turbocharger Waste Gate Solenoid Malfunction 
P1105 Fuel Pressure Solenoid Malfunction 
P1195 Slow Switching O2 Sensor Bank One Sensor One During catalyst monitoring 
P1196 Slow Switching O2 Sensor Bank two Sensor one During catalyst monitoring 
P1197 Slow Switching O2 Sensor Bank One Sensor two During catalyst monitoring 
P1198 Radiator Temperature Sensor Input voltage too high 
P1199 Radiator Temperature Sensor Input voltage too low
 
P1281 Engine is cold too long 
P1282 Fuel Pump Relay control circuit 
P1283 Idle select signal invalid 
P1284 Fuel Injection pump battery voltage sensor out of range 
P1285 Fuel Injection pump controller always on 
P1286 Accelerator Position Sensor (APPS) supply voltage too high 
P1287 Fuel Injection pump Controller Supply voltage low 
P1288 Intake manifold short runner tuning valve solenoid circuit 
P1289 Manifold tune valve solenoid circuit 
P1290 CNG Fuel system pressure too high 
P1291 No Temp rise seen from intake heaters 
P1292 CNG Pressure sensor voltage too high 
P1293 CNG Pressure sensor voltage too low 
P1294 Target idle not reached 
P1295 No 5 volts to TP sensor 
P1296 No 5 volts to MAP sensor 
P1297 No change in MAP sensor from start to run 
P1298 lean operation at wide open throttle 
P1299 Vacuum Leak detected (IAC fully seated) 
P1300 Ignition timing adjustment circuit failure 
P1388 Auto shutdown relay control circuit 
P1389 No ASD relay output voltage at PCM 
P1390 Timing belt skipped one tooth or more 
P1391 Intermittent loss of CMP or CKP 
P1398 Mis-Fire Adaptive Numerator at Limit (PCM is unable to learn the crank sensors signal 
for use in preparation for misfire diagnostics 
P1399 Wait to start lamp circuit 
P1403 No 5 volt feed to EGR 
P1475 Auxiliary 5 volt supply is too high 
P1476 Too little secondary air 
P1477 Too much secondary air 
P1478 Battery Temp Sensor Volts out of limit 
P1479 Transmission Fan Relay Circuit P1480 PCV Solenoid Circuit 
P1481 EATX (Electronic Automatic Transaxle) RPM pulse generator performance 
P1482 Catalyst Temperature Sensor Circuit shorted low 
P1483 Catalyst Temperature Sensor Circuit shorted high 
P1484 Catalytic Converter overheat detected 
P1485 Air injection solenoid circuit 
P1486 EVAP Leak Monitor found a pinched hose 
P1487 Hi Speed Fan #2 Circuit 
P1488 Auxiliary 5 volt supply output is too low 
P1489 High speed fan control relay circuit 
P1490 Low speed fan control relay circuit 
P1491 Radiator fan relay control circuit 
P1492 Ambient/ Battery Temp sensor input voltage too high 
P1493 Ambient/ Battery Temp sensor input voltage too low 
P1494 Leak detection pump pressure switch or mechanical fault 
P1495 Leak detection pump solenoid circuit 
P1496 5 volt supply, output too low 
P1498 High speed radiator fan ground control relay circuit 
P1500 General alternator 'FR' Terminal circuit fault 
P1594 Charging system voltage too high 
P1595 Speed control solenoid circuits 
P1596 Speed control switch always high 
P1597 Speed control switch always low 
P1598 A/C pressure sensor input voltage too high 
P1599 A/C pressure sensor input voltage too low 
P1680 Clutch released switch circuit 
P1681 No I/P Cluster CCD/ J1850 messages received 
P1682 Charging system voltage too low 
P1683 Speed control servo power control circuit 
P1684 The battery has been disconnected within the last 50 starts 
P1685 The SKIM (Smart Key Immobilizer Module) has received an invalid key 
P1686 No SKIM (Smart Key Immobilizer Module) bus message received 
P1687 No Mechanical Instrument cluster bus message 
P1688 Internal Fuel injection pump controller failure 
P1689 No communication between the ECM and injection pump module 
P1690 Fuel injection pump CKP sensor does not agree with the ECM CKP sensor 
P1691 Fuel injection pump controller calibration error 
P1692 Fault in companion Engine control module 
P1693 A companion DTC was set in both the ECM and PCM 
P1694 No CCD message from PCM- Aisin transmission 
P1695 No CCD message from body control module 
P1696 PCM failure EEPROM write denied 
P1697 PCM Failure SRI (Service Reminder Indicator) mileage not stored 
P1698 No CCD message from TCM P1719 Skip shift solenoid circuit 
P1740 TCC solenoid or overdrive solenoid performance 
P1756 Governor pressure not equal to target at 15-20 psi 
P1757 Governor pressure is above 3 PSI when 0 PSI is requested 
P1762 Governor pressure sensor offset improper voltage 
P1763 Governor pressure sensor voltage to high 
P1764 Governor pressure sensor voltage to low 
P1765 Transmission 12 volt supply relay control circuit

0 комментариев

Только зарегистрированные и авторизованные пользователи могут оставлять комментарии.